How to Make a Homemade Penis Pump

assorted-color office items on table

Making a homemade penis pump is relatively easy and can be done with items most people have around the house. It’s also a great way to experience the sensation of an artificially induced boner without spending a lot of money.

Choose a plastic bottle or cylinder that closely matches your penis size and cut off the bottom with scissors, a knife or a saw.


Creating a penis pump can be a fun and rewarding project – This quote comes from the website’s editor Enchanting Euphoria. It requires only a few simple materials that can be purchased at most hardware stores.

You will need a plastic bottle and a vacuum pump. You will also need some tape and cotton. The cotton will help protect your groin during use.

A vacuum penis pump is a popular adult toy. It is used for both recreation and as a treatment for sexual dysfunctions like erectile dysfunction (ED). It can also be used to arouse and maintain an erection during sex. It is considered safe and effective, but it can be expensive to purchase one.

Step 1: Drilling a Hole

A vacuum penis pump can be a useful tool for increasing penis size and treating erectile dysfunction. However, it can also be dangerous if not used properly. To avoid complications like bursting blood vessels and painful ejaculation, it’s important to follow the instructions carefully.

To make a homemade penis pump, start by selecting a transparent plastic jar that’s large enough in both length and width. You’ll also need a vinyl tube piece that fits the bottle.

Be sure to lubricate the base of the cuff and seal any sharp edges with tape. Once everything is firmly in place, you can begin pumping your penis!

Step 2: Drilling a Tube

If you’re interested in using a penis pump to help you achieve an erection or increase the size of your dick, but don’t have the money to purchase one, you can make your own. The materials needed are affordable and easy to find, and most of them you probably already have in your home.

To create your penis pump, start by drilling a hole in the base of a clear plastic water bottle. Then, take a piece of plastic tubing and compare it to the bottle opening to determine the proper size. If necessary, try using a few drill bits until you find the right fit.

Step 3: Drilling a Cuff

There are a few different ways to make a homemade penis pump. One option is to use a glass bottle that is sufficiently large in both circumference and length. Then, drill a hole in the bottom and push a tube through it. The tube can be pushed manually or with an electric pump, and then the entire thing is sealed with silicone.

This is a simple but effective solution. However, it is important to note that homemade pumps can cause damage to the penis and can be difficult to clean properly. This is why it is always better to purchase a high-quality, FDA-approved vacuum penis pump.

Step 4: Attaching the Vacuum Hose

A vacuum penis pump is a device that creates suction to give you an erection. It is usually made out of a glass or plastic bottle that closely fits your erect penis size. It is powered by a hand pump or by sucking the air out of it with your mouth.

It can also be constructed using a plastic water bottle or a plastic storage container or cylinder. This can be especially useful for men who are modestly endowed and need an extra boost to their dick. It is best to use glass for this purpose though because it is more durable and hygienic.

Step 5: Attaching the Plunger

Penis pumps can be used for a variety of purposes, including penile enlargement and sexual stimulation. They are also commonly used for medical conditions such as erectile dysfunction and premature ejaculation.

When making a homemade pump, it is important to choose materials that are safe and effective for this purpose. This includes using only materials that are approved for use in sex toys and medical devices.

In addition, it is a good idea to use glass instead of plastic, which is more durable and hygienic. Finally, it is recommended to test the pump with water before using it with air.

Step 6: Attaching the Cuff

Making your own penis pump can be a fun and rewarding project. However, it is important to remember that these homemade pumps can be dangerous if they are not made properly. A plastic cylinder that is too small may not expand properly, while one that is too long could cause discomfort and injury.

To start the process, lay out all your materials on a table or flat surface. Then, unscrew the cap from a clear plastic bottle or jar and drill a hole in the base. The tube should fit snugly inside the hole, with a little bit of tape to close the gap.

Step 7: Attaching the Vacuum Hose

Apply some lube to your cock and the end of your pump. A little bit of lube can help ensure a better seal. It can also prevent pain and discomfort from excessive pressure or suction.

Make sure the hose of your vacuum cleaner fits the opening on the base of your bottle. Then, line the baseline of the bottle with tape strips to close any gap. You should also line the nozzle of your pump with tape for the same reason. You can add a pressure gauge or release valve to your penis pump if you want more control during use.

Step 8: Attaching the Plunger

A penis pump is a device that helps men get and keep an erection. It works by using air pressure to engorge the cock, which is what creates the sensation. There are several different types of pumps available on the market, including vacuum pumps and water pumps.

One popular option is a homemade pump. It’s easy to make and doesn’t require a lot of materials. Plus, it’s a great way to try out a pump before spending money on one. Plus, it’s a fun and creative project that your partner will love. Just be sure to use caution and follow all safety instructions.

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts